Super-micro-computer P4SCT Uživatelský manuál stáhnout pdf (Strana 91)

100

Appendix C: Software Installation Instructions

C-15

5. Repeat Step 4 so that both drives to be initialized are selected (as

shown in the screen below).

6. Press Enter.

7. Read the warning message as shown in the screen.

8. Make sure that you have selected the correct disk drives to initialize.

If correct, type Y to continue.

1 2 ... 86 87 88 89 90 91 92 93 94 95 96 ... 99 100

SUPER 1
About This Manual 3
Manual Organization 3
Table of Contents 4
Chapter 3: Troubleshooting 5
Chapter 4: BIOS 6
Appendices: 6
Chapter 1 7
Introduction 7
Contacting Supermicro 8
UPER P4SCT/P4SCT+/P4SCT+II 10
Connectors Description 11
E875P & E7210 12
Processor 0 12
Motherboard Features 13
Canterwood ES (E7210) 15
Features 16
Serial ATA(SATA) Interface 16
64-bit PCI/PCI-X Interface 16
1-3 PC Health Monitoring 17
1-5 Power Supply 19
1-6 Super I/O 20
Chapter 2 21
Installation 21
2-4 Installing DDR Memory 24
Memory Speeds 25
Front Control Panel 26
2-6 Connecting Cables 27
Reset Connector 28
Overheat LED (OH) 28
GLAN1 LED 29
GLAN2 LED(*P4SCT+/ 29
P4SCT+II Only) 29
Power_LED Connector 30
*IDE LED (*See the note 30
Speaker Connector 31
NMI Button 31
IR Connector 31
Fan Headers 32
Serial Ports 32
Chassis Intrusion 33
Wake-On-LAN 33
B. GLAN1 & GLAN2 34
A. VGA Header 34
C. SMB Header 34
Universal Serial Bus (USB) 35
ATX PS/2 Keyboard and 35
PS/2 Mouse Ports 35
A. Wake-On Ring 36
B. Keylock Enable 36
B. Intel SATA LED 37
C. Marvell SATA LED 37
A. Standby PWR LED 37
2-7 Jumper Settings 38
USB Wake-Up (*USB1/2 39
Marvell's SATA Enable 39
(*P4SCT+/P4SCT+II Only) 39
Watch Dog Enable/Disable 40
GLAN2 Enable/Disable 41
Keyboard Wake-Up 41
Front Side Bus Speed 42
VGA Enable/Disable 42
Connections 43
IDE Connectors 44
Floppy Connector 44
A. AGP Slot 45
Chapter 3 47
Troubleshooting 47
Memory Errors 48
Chapter 4 53
4-2 Running Setup 54
4-3 Main BIOS Setup 54
4-4 Advanced BIOS Setup 56
USB Legacy Support 59
CPU THRM-Throttling 59
Keyboard Input Clock 59
4-4.4 PnP Configuration 61
4-4.5 Console Redirection 62
4-4.6 Hardware Monitor 63
4-5 Security 65
4-6 Boot 66
4-7 Exit 67
Load Fail-Safe Defaults 68
Load Optimized Defaults 68
Discard Changes 68
Appendix A 69
BIOS POST Messages 69
Appendix C 77
Operating System 77
ATA Operate Mode 78
Combined Mode: 78
Enhanced Mode: 78
(Enhanced Mode) 79
Managing Arrays 81
Creating Arrays 83
RAID 1 Init 85
Initializing Disk Drives 89
Rebuilding Arrays 92
Using the Disk Utilities 93
Adaptec and the OS 96
ATA RAID Controller Driver 97
Supero Doctor III 98

Komentáře k této Příručce

Žádné komentáře

Super-micro-computer P4SCT Uživatelský manuál Strana 91

Komentáře k této Příručce

Související produkty a manuály pro Hardware Super-micro-computer P4SCT