Super-micro-computer 5010E Uživatelský manuál Strana 60
- Strana / 128
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
5-22
SUPERSERVER 5010H/5010E Manual
Jumper
Position
Open
Closed
Definition
Enabled
Disabled
LVD CH A SCSI
Termination
Jumper Settings (JPA1)
LVD Channel A SCSI Termination
Enable/Disable (5010H only)
Jumper JPA1 allows you to enable or disable
termination for the LVD Channel A SCSI con-
nector. The normal (default) position is open
to enable SCSI termination. See the table on
the right for jumper settings.
LVD Channel B SCSI Termination
Enable/Disable (5010H only)
Jumper JPA2 allows you to enable or disable
termination for the LVD Channel B SCSI con-
nector. The normal (default) position is open
to enable SCSI termination. See the table on
the right for jumper settings.
Jumper
Position
Open
Closed
Definition
Enabled
Disabled
LVD CH A SCSI
Termination
Jumper Settings (JPA2)
SCSI Enable/Disable
(5010H only)
Jumper JP34 allows you to enable
or disable all onboard SCSI. The
normal (default) position is en-
abled. See the table on the right
for jumper settings.
Jumper
Position
1-2
2-3
Definition
Enabled
Disabled
SCSI Enable/Disable
Jumper Settings (JP34)
- SUPER 1
- About This Manual 3
- Manual Organization 3
- Manual Or 5
- Chapter 3: System Interface 6
- Chapter 4: System Safety 7
- Chapter 7: BIOS 8
- Appendices: 9
- Chapter 1 11
- System Power 12
- SCSI Subsystem (5010H only) 12
- Control Panel 12
- Cooling System 13
- Figure 1-1. Rear I/O Panel 13
- Rear I/O Panel 13
- Chipset Overview 14
- Processors 15
- Onboard SCSI (5010H only) 15
- PCI Expansion Slots 15
- Onboard Controllers/Ports 16
- Other Features 16
- Headquarters 17
- European Office 17
- Asia-Pacific 17
- Chapter 2 19
- Server Installation 19
- Choosing a Setup Location: 20
- Rack Precautions: 20
- Server Precautions: 20
- Installing the Chassis Rails: 22
- Installing the Rack Rails: 22
- (with SCSI Installed) 26
- (with IDE Installed) 27
- Chapter 3 31
- System Interface 31
- 3-3 Control Panel LEDs 32
- 3-5 Power Supply Switch 33
- 3-6 Motherboard LEDs 33
- Chapter 4 35
- System Safety 35
- 4-3 ESD Precautions 37
- Tools Required 39
- Precautions 39
- Unpacking 40
- Connecting Data Cables 41
- Connecting Power Cables 41
- Connecting the Control Panel 42
- 5-5 Installing Processors 43
- 5-4 I/O Ports 43
- 5-6 Installing Memory 45
- 5-7 Adding PCI Cards 46
- 370SSR+ Motherboard 47
- 370SSE+ Motherboard 47
- SUPER 370SSR+ 48
- SUPER 370SSE+ 50
- 5-8 Connector Definitions 52
- NIC1 LED 53
- NIC2 LED 53
- Power LED 53
- Overheat LED (JOH) 54
- Serial Ports 55
- Fan Headers* 55
- Universal Serial Bus (USB) 55
- ATX PS/2 Keyboard and 56
- PS/2 Mouse Ports 56
- LAN1/LAN2 Ports 56
- Wake-On-Ring 57
- Wake-On-LAN 57
- Connector 58
- CMOS Clear 59
- Speaker Enable/Disable 59
- Onboard LAN Enable/ 59
- IDE Connectors 61
- Floppy Connector 61
- Ultra160 SCSI 62
- Connectors 62
- 6-2 Control Panel 64
- System Fan Failure 65
- Replacing System Cooling Fans 65
- Accessing the Drive Bays 66
- Power Supply Failure 70
- Replacing the Power Supply 70
- Chapter 4 73
- 7-2 BIOS Features 74
- 7-3 Running Setup 74
- The Main BIOS Setup Menu 75
- 7-4 Advanced Chipset Setup 76
- Super IO Configuration 78
- IDE Configuration 80
- Floppy Configuration 83
- Boot Settings Configuration 84
- Event Log Configuration 87
- GMCH Configuration 88
- ICH2 Configuration 92
- The settings for 94
- 7-6 PCI PnP Setup 96
- 7-7 Power Setup 100
- Boot Device Priority 106
- Hard Disk Drives 107
- Removeable Devices 107
- ATAPI CDROM Drives 107
- Supervisor Password 108
- User Password 108
- Change User Password 109
- Clear User Password 109
- Boot Sector Virus Protection 109
- Change Supervisor Password 109
- Exit Saving Changes 110
- Exit Discarding Changes 110
- Load Optimal Defaults 111
- Load Failsafe Defaults 111
- Discard Changes 111
- Notes 112
- Appendix A 113
- AMI BIOS Error Beep Codes 114
- Appendix B 115
- AMIBIOS POST Checkpoint Codes 115
- B-2 Bootblock Recovery Codes 116
- <DEL> 118
- Hit <DEL> 118
- <WAIT...> 119
- B-4 Bus Checkpoint Codes 123
- UPERSERVER 5010H/5010E Manual 124
- Appendix C 125
- List of Figures 125
- Appendix D 127
- System Specifications 127
Související produkty a manuály pro Hardware Super-micro-computer 5010E
Hardware Super-micro-computer X8STE Uživatelský manuál
(103 stránky)
(103 stránky)
© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.019 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce